 |
 |
Instructions for the
PrintLab 3503R
16. Care and Maintenance
Daily maintenance
1. Clean paper-loading tray with cloth. Never rinse, water can damage electronics!2. Close water tap after cleaning has finished.
3. Clean angled paper guide mounted at rack 2 with a cloth.
4. Check filling level of reclamation containers and cubitainers.
5. To reduce formation of condensation, leave the protection lid over the paper-loading tray open, when not actually spooling prints.
6. If the machine is ready for operation after turning on, fill tanks 1 and 2 with water up to the overflow, to compensate for evaporation. Thus, evaporation is compensated. This is important in order to avoid an increase of the chemical concentration.
Weekly maintenance
In the normal order of processing, at least once a week, a minimum of one third of the contents of tanks (1 and 2) should be replenished, as replenisher substitutes the original chemical content By pushing the ENTER-Key, the processed area in m2 can be displayed and multiplied by the replenisher rate. If at least 1665 ml has not not been added to the tank, an addition of fresh working solution can be made. Should the unit not be continuously used, please contact your supplier of chemicals. They can offer you several additives to protect the chemicals from oxidation.Every two weeks
1. Clean housing parts with a wet cloth.2. Rinse racks with running fresh water outside of the processor.
3. Clean the filters of Tank 1 and Tank 2, and reinsert them.
4. Clean light-traps with a brush.
Cleaning every 3-4 months or when changing the process
Please note the security prescriptions in paragraph 111. Run cleaning program.
2. Turn off the machine.
3. Drain the chemicals from all containers and cubitainers.4. Clean the containers and cubitainers with Processor Clean II (dissolve Processor Clean completely in hot water before using it).
5. Fill up the containers and cubitainers with fresh cleaning solution.
6. Place suction hoses in containers and cubitainers.
7. Place containers in wall mount and switch on processor.
8. Keep processor running at 35 C° with the lid on. During this time the sensors need to be covered with a sheet of paper.
9. Turn off processor.
10. Drain cleaning solution from all containers and cubitainers.
11. Rinse containers and cubitainers with fresh water.
12. Fill containers and cubitainers with fresh water.
13. Place suction hoses again into cubitainers.
14. Place containers in wall mount and switch on processor.
15. Keep processor switched on with cover lid closed for about 5 minutes. During this time the sensors should be covered with a sheet of paper.
16. Run cleaning program.
17. Drain water from containers and cubitainers.
18. Empty draining hoses completely. This is Important to avoid contamination
19. The cleaning with fresh water after the use of Processor Clean II should be done at least twice (point 12). After filling the processor with new solutions, it is advisable to run a test strip for densitometric control.
Maintenance every 12 months
1. Clean helical drive and apply appropriate grease. (#95465)2. Clean light-trap.
3. Replace hoses of replenisher pumps. (#93008 set of two)
4. Adjust replenisher pumps (service menu 26 27)
5. Check filling level of reclamation containers and cubitainers.
6. Rinse cubitainers.
If you have any questions, contact us utilizing one of the following methods:
Equipment or Processing Questions:
- Phone: Customer Service Department (734) 205-9421
e-mail: tech@jobo-usa.comRepair Questions:
- Phone: Repair Department (734) 205-9420
- e-mail: repair@jobo-usa.com
JOBO Contacts
- Telephone (734) 677-6989
- Fax: (734) 677-6963
- Postal address
- P.O. Box 3721, Ann Arbor, MI 48106
- Shipping Address
- 4401 Varsity Drive, Suite D, Ann Arbor, MI 48108
- Electronic mail
- Sales: sales@jobo-usa.com
- Equipment & Processing Questions: tech@jobo-usa.com
Repair Information: repair@jobo-usa.com- Shipping or Billing Questions: help@jobo-usa.com
Webmaster: webmaster@jobo-usa.com
Back to Top
Send mail to webmaster@jobo-usa.com with questions or comments about this web site. Copyright © 1997-2005 JOBO Fototechnic, Inc. All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright to all of the photographs displayed on this site is owned by each of the photographers. You may not sell, publish, license or otherwise distribute any photographs without the written permission of the photographer.
This page last updated on 03/20/02