 |
 |
Instructions For The JOBO CPE-2 Plus Processor
#4065 (CPE-2 Plus) & #4069 (CPE-2 Plus Starter Kit)
Section 5
Note: This is a very detailed and profusely illustrated web page. It will take a little time to load it into your browser. Get a cup of coffee and stretch while it is downloading.
It is worth the wait!
[CPE-2 Plus Starter Kit]
Information needed to operate your processor successfully with a wide variety of processes is included in this instruction manual. We urge you to read all the basic information contained in Section One and Section Two. Then read the pages of Section Three that describe the processes you wish to use. If you are having problems with your processor or processing, see the pages of Section Four. For conversions, tables and lists see Section Five.
If you have obtained this instruction manual as a replacement to earlier editions, use the process recommendations in this web page (where they are different), not the recommendations in the earlier manual(s). These instructions reflect the changes that have been made in film, paper, and chemicals since the original book was written. (If you already have processing procedures that completely satisfy you, don't change them just to match the directions in this web page.)
There are three types of special notations or cautionary information in this manual: Note, Caution, and Warning. The type and format of each is listed below:
Note: Text in this format is informative. It contains additional details to explain the basic information presented.
Caution: Text in this format presents important procedural information. Failure to follow these instructions could adversely affect the processing of your film or paper.
WARNING: Text in this format presents critical information. Possible damage to your equipment or personal injury could result from not following these instructions!
Copyright © 1997 by JOBO Fototechnic, Inc. All rights reserved. No portion of this web page may be reproduced in any form without express written consent from JOBO Fototechnic, Inc.
Every effort was made to include up-to-date and accurate information in this manual. All manufacturers, including JOBO, maintain the right to change specifications for their products. Changes may be made to specifications without notice. For the most current product specifications and usage, contact the manufacturer.
JOBO makes no claim for the accuracy or usability of other manufacturers' information contained in this manual. The processing recommendations included in this manual may not be optimal for every situation. If you require specific results, test all process instructions for suitability.
JOBO is not liable for any damages, direct or consequential, occurring from the use or misuse of information contained in this manual.
Credits:
Author: Damon Dean
JOBO Contributors: Ken Owen, Chris Mishler, Sam Proud, Paul Rowe
Manual part number 66051. Revision 06/97.
[CPE-2 Plus]
Section 2: General Processing Instructions
Section 5: Appendices
- Processor Specifications; CPE-2 Plus
- Accessories
- Spare Parts
- Fuse Replacement
- CPE-2 Plus Improvements
- Using This Manual for the Original CPE-2 Processor
- Cogs and Magnets(linked to additional page)
- JOBO Chemicals (all are links to additional pages)
- Tetenal Chemicals (all are links to additional pages)
- Conversion Formulas and Tables, Metric and English (linked to additional Page)
- Tank and Drum Capacities (linked to additional page)
- 1500 Series Tanks (Illustrations)
- 2500 Series Tanks (Illustrations)
- 2800 Series Drums (Illustrations)
- Trademarks
Processor Specifications; CPE-2 Plus
- Tempering bath capacity: 2 gallons (7.6 liters)
- Base Area: 12 x 16 inches (30 x 40 cm), including overhang
- Chemical Solution Capacity: Four 260 ml (8 oz.) graduates; four 600 ml (20 oz.) bottles (optional six bottles only with E-6 Conversion Kit #4061)
- Voltage: 120 Volts, 60 cycles (Hz) AC
- Power Consumption: 300 Watts, 2.5 Amps
- Tanks and Drums:
- 1510
- 1520
- 1526 (1520 and 1530 together)
- 1530 (extension module used with 1510 or 1520)
- 1540 (1510 and 1530 together)
- 2517
- 2521/2523
- 2551/2553
- 2820
- 2830
- 2840
- 2870 (extension module used with 2820 to make 2830)
Note: Tanks or drums with a last digit of '3' only work with the JOBO Lift accessory. Tanks with a last digit of '1' come with an attached magnet (#1504.) All tanks or drums (except extension modules) with a last digit of '0' require a magnet accessory (#1504), mounted on the bottom, to be used on the CPE-2 Plus processor (without the JOBO Lift). The 1526 Combo Drum does not come with either a magnet or cog. To use any of the above tanks or drums with the JOBO Lift (except the ones already equipped with a cog), you must add a Cog (#1505). Install it in the lid of the tank or drum.
- Reels:
- 1501 (35 mm, 1 or 2 120, 220)
- 1502 (2 110, or 16 mm 5' or 1.5 M maximum)
- 1555 (35 mm Stainless Steel)
- 1557 (120 Stainless Steel)
- 1559 (220 Stainless Steel)
- 2502 (35 mm, 1 or 2 120, 220)
- 2509N (4 x 5", 6 x 9 cm, 9 x 12 cm, up to six sheets)
- 2517 (70 mm, 5' or 1.5 M maximum)
- 2518 (2 1/4 x 3 1/4" up to six sheets)
Additional or replacement: Black Bottle 600 ml (#3370), White Bottle 600 ml (#3371), Graduate 260 ml (3308), Color Thermometer (#3321).
For other JOBO products that will enhance the use of your processor, check your JOBO catalog, talk to your JOBO dealer, or call JOBO Customer Service at (734) 677-6989, ext. 4721. Our hours are from 8 a.m. to 5 p.m. Eastern Time, Monday through Friday, but our voice mail answering system is available 24 hours a day. You may fax us at (734) 677-6963. E-mail us at tech@jobo-usa.com. If you wish to write us, our address is: JOBO Fototechnic, P. O. Box 3721, Ann Arbor, MI 48106-3721, USA. We will be happy to help you.
The JOBO Lift (#4062) accessory makes it easier to dump and fill the chemical and rinse steps. Instead of grabbing the tank off the processor, removing the tank cap, pouring out the solution, pouring in the next solution, replacing the tank cap, and putting the tank back on the processor, all you do is pull back on handle to drain the tank, then lower the handle and fill the tank.
E-6 Conversion Kit
Use the #4061 E-6 Conversion Kit to transform your CPE-2 Plus to a full six-step E-6 processor. The conversion kit comes with a replacement bottle rack and two 600ml bottles (to be used with the four bottles that come with the processor).
JoMate Conversion Kit
Use the JoMate Conversion Kit #200019 to transform your CPE-2 Plus rotary-style film and print processor to a 8x10" temperature controlled dip-n-dunk style print processor. You'll then be able to replenish your chemicals to save money. The JoMate comes with an installation rack, four 8x10" print slots, and a #200007 Print Clip. (The CPE-2 Plus shown grayed out is available separately).
- Parts for the Motor Head CPE-2 Plus
- Parts for the Motor Head CPE-2 (Only for Non-Plus)
- Parts for the Tempering Bath
- Parts for the JOBO Lift
- Parts for the Roller Block
- Parts for JOBO Film Tanks and Print Drums
Before 1991, an earlier version of the CPE-2 Plus processor was provided. This processor was named the CPE-2 (with no 'Plus'). The non-Plus units looked similar, but were very different internally. Units before this transition (CPE-2 #4060, and CPE-2 Starter Kit #4067), use a different rotation motor, magnet or cog, and associated circuit board. These processors can be identified by examining serial number label or the rotation motor shaft. The newer units (Plus) have a tapered shaft, threaded on the inside. Previous units have a cylindrical, non-tapered shaft that is not threaded. When replacing the rotation motor or circuit board, be sure to determine which version you have before obtaining these parts. The new motor magnet or motor cog is tapered to accommodate the tapered shaft. These motor magnets or cogs are secured with a hex-headed screw. (The older version of drive magnets and cogs are attached with a slot headed screw.) Both the magnets for the tanks and the cogs for the lids have not changed. A thermal overload reset mechanism was added to the 'Plus' units, and the reversal mechanism was changed from mechanical to electronic. Because all the internal components are different, it is not possible to upgrade a non-Plus processor to a 'Plus' processor. For clarity, the older components are identified in the list below with a star '*'. (The star is not part of the part identification number or description.)
WARNING: If you are unsure as to the appropriate selection of replacement parts, contact JOBO for assistance. Use of inappropriate replacement parts may damage your processor or lessen the performance or life of the processor.
Parts for the Motor Head CPE-2 Plus (#4065):
- # 94064 Circuit Board for CPE-2 Plus, (110 volt - plus only)
- # 32025A Rotation Motor without shaft (plus only)
- # 93029 Shaft with Nut for Rotation Motor (tapered - plus only)
- # 95442 Rotation Magnet with Hex Screw for motor shaft (for motor w/o lift only - plus only)
- # 95299 Cog Gear (black, for motor with lift only - plus only)
- # 26003 Heat Indicator Lamp, 110 volt
- # 95178 Thermostat (with probe)
- # 95250 Thermal Overload Reset (with probe - plus only)
- # 27010 Fuse, 3.15 amp, type T (slow blow), 250 volt
- # 93035 Heating Element, 110 volt
Parts for the Motor Head CPE-2 (#4060) (Only for Non-Plus):
- # 94002 * Circuit Board for CPE-2, (110 volt - non-plus only)
- # 32007 * Rotation Motor (with non tapered shaft - non-plus only)
- # 95001 * Rotation Magnet (for motor w/o lift only - non-plus only)
- # 95523 * Cog Gear (black, for motor with lift only - non-plus only)
- # 95226 * Micro Switch for Reversal (non-plus only)
- # 3371 600 ml Bottle, White
- # 3370 600 ml Bottle, Black
- # 3380 600 ml Bottle Set (3 white, 1 black)
- # 05042 Cap for 600 ml Bottle
- # 3308 260 ml Graduate
- # 3318 Graduate Kit (four #3308 graduates)
- # 95520 Set of two Processor Leveling Wedges
- # 15018 Ceramic Spacer (bottom of trough)
- # 3321 Color Thermometer
- # 35054 Push Pin for Bottle Rack
- # 13008 Cone for bottle rack support
- # 91045 Bottle Rack (4-bottle, 4-graduates) - requires two (2) #35054 push pins
- # 4061 E-6 Conversion Kit (Accessory Rack for 6-600 ml Bottles, with two (2) 600 ml Bottles)
- # 07083 White Retaining Clip (old style lift only)
- # 92157 Black Retaining Clip Assembly (new style lift only)
- # 92158 Red Cap for Lift (new style lift only)
- # 07109 Lift Handle Attachment (black hub only)
- # 95186 Lift Handle Assembly (includes hub, tube and cap)
- # 34200 Screw for the Lift Handle
- # 95200 Transfer Gear Set (2 sets)
- # 34901 Washer for Transfer Gear (old style lift only)
- # 95465 Grease Syringe (for lift gears)
- # 95215 Roller Block Assembly for Lift Arm
- # 95183 Roller Block Assembly for Processor Trough
- # 07067 Roller Extensions (angled arms) for roller block
- # 07007 White Rollers for roller block
- # 92167 Black Rollers with stainless steel axle (substitute for 07007 with 07067 extensions attached)
Parts for JOBO Film Tanks and Print Drums:
- # 03042 Funnel, light trap for 1500/2500 Film Tanks (2800 with stopper, lift only)
- # 03046 Red Cap, for lid of 1500/2500/2800 series
- # 03049 Beaker, for lid of 1500/2800 Paper Drums
- # 04043 Center Core for single reel with base (1510, 1540)
- # 04044 Center Core for two reels with base (1520, 1526, 2521, 2523, 2551, 2553)
- # 04045 Center Core for three reel extension (1526, 1530, 1540, 2553)
- # 91034 Inversion Lid With Ring for 1500 series (no funnel, beaker, or cap)
- # 91036 Inversion Lid With Ring for 2500/2800 series (no funnel, beaker, or cap)
- # 1505 Cog (converts inversion lid to cog lid for use on lift)
- # 07095 Cog Lid Washer (Red)
- # 15042 Cog Lid Stopper (makes funnel #03042 a light trap for prints, used with lift)
- # 1503 Cog Lid for 1500 series (with funnel)
- # 2503 Cog Lid for 2500/2800 series (with funnel and stopper)
If the processor does not function, the fuse may be blown. If nothing at all works on the processor, first check that the power cord is plugged in, and the outlet it is plugged into is 'live.' If the only thing that does not work is the heating of the water bath, reset the thermal overload button. To check and replace the fuse, use the procedure listed below.
Turn off the processor and unplug the power cord. Drain all the water from the trough. Remove the JOBO Lift (if attached). Remove the five slot-headed screws in the top of the motor housing. Carefully remove all three knobs.
Gently remove the top cover of the motor head, being careful to not stress the switch shafts. Set the top cover aside. (The heat indicator light is attached to the top cover and will limit how far the lid may be placed from the bottom section.)
Locate the fuse. (See below for location, function and specifications of the fuse.) Verify that the power cord is unplugged. Carefully remove the fuse from its holder. (You may use a small screw driver or needle-nose pliers.) Replace the fuse with the designated replacement. Do not substitute a differently rated fuse! Verify complete seating of the new fuse. Reverse the disassembly procedure listed above to reassemble motor head. Test the function of the reassembled motor head. If your processor blows another fuse, contact JOBO for repair assistance.
WARNING: Always unplug the power cord before opening the motor head. Make sure that water does not get into the motor head. If there is any water (or chemicals) inside the motor head, do not plug in power cord, contact JOBO for repair assistance. Never replace a fuse with a different rating. If the processor continues to blow fuses, or there is any function not working correctly, contact JOBO for repair assistance. Do not use the processor if it is not functioning properly.
WARNING: If there is a label beside the fuse indicating a different value (other than what is listed below) for the fuse, contact JOBO for assistance.
Notes:
The screws holding the circuit board to the bottom of the motor head are deliberately not turned down all the way. They are left loose (so the circuit board can move) to prevent the switches from being damaged when the cover is installed or removed. Do not over-tighten these screws.
Visual inspection of a fuse is not a reliable method for determining if the fuse is good. Use a 'continuity checker', or 'Ohm meter' to verify fuse condition. If you do not have access to a checker or meter, replace the suspect fuse with a new, same rated fuse.
The fuse for the CPE-2 Plus is rated at 250 Volts. 250 Volt fuses work with any voltage less than or equal to 250 Volts. You do not need '110 Volt fuses' for processors using 110 Volt power sources.
Main Circuit Fuse
- Type: 3.15 Amp 250 Volt (rated) Type T (slow blow), JOBO part #27010
- Processor: CPE-2 Plus and CPE-2
- Protection: All electrical circuits
- Failure Symptoms: Nothing works
- Location: Circuit board, near the On/Off switch
You may be wondering what the differences are between the original CPE-2, and the CPE-2 Plus Processors. Briefly, they are:
- A thermal overload was been added. This device gives additional protection from overheating when there is not enough water in the tempering bath. If the processor overheats, a circuit breaker trips. Pressing the white button will reset the circuit breaker. If the thermal overload is tripped, the processor will not heat.
- The original rotation motor was replaced with a more robust motor. This increases the reliability of the unit with heavy loads.
- A more secure mount was made for the magnet or cog, on the end of the motor shaft.
- The original mechanical device used for switching the rotation direction of the motor was replaced with an electronic switching circuit. There are no mechanical parts to wear out, or get out of alignment.
- The two speeds for rotation have been replaced with a single speed, electronically metered at 75 rpm. The original speed of `2' was also about 75 rpm. Deleting the slower speed of `1' was done because all modern processes worked better at the faster speed.
- The motor housing, transformer, and the entire circuit board were replaced to accommodate the above changes.
- The JOBO product numbers were changed for the processor and the Starter Kit.
Note: Because of these extensive changes, it is not possible to upgrade a CPE-2 to a CPE-2 Plus.
Using This Manual for the Original CPE-2 Processor
You may use this instruction book for the original CPE-2 Processor, with the following changes and recommendations:
- When turning on the rotation motor, use the setting of `2'.
- The magnet and the drive cog have been changed. Use part number #95001 for the magnet, and #95523 for the drive cog on the original processor.
- Make sure that the three fingered reversal mechanism (it looks like a 2" white `chicken foot'), located next to the rotation motor shaft, is pointed towards the motor shaft. This allows the reversal switch to function.
- Be sure to fill the tempering bath with water whenever you are using the processor. This will prevent overheating.
- Do not exceed the maximum quantity (600 ml) of chemicals or water (in a tank or drum), for any process.
- Do not use the stainless steel reel system, as its additional weight puts too much strain on the rotation motor.
Tanks and Drums For the CPE-2 Plus Processor
[1510, 1520, 1530, 1540, 1526]
- 'Agfa', 'Agfachrome' and 'Agfacolor' are registered trademarks of Agfa Gevaert, a division of Bayer.
- 'Kodak', 'Kodachrome', 'Ektachrome', 'Lumiere', 'Elite', E-6, C-41, EP-2, RA-4, R-3, R-3000, D-76 and X-Tol are registered trademarks of Eastman Kodak Co.
- 'Fujichrome', 'Velvia', 'Sensia', 'Provia' and 'Reala' are registered trademarks of Fuji Film Co.
- 'Ilfochrome' and 'Cibachrome' are registered trademarks of Ilford, Inc.
- 'Tetenal' is a registered trademark of Tetenal Photowerk GmbH & Co.
Use of a trademarked name does not imply an endorsement by the manufacturer. The lack of a trademark does not indicate a challenge to the ownership of a product.
Every effort was made to include up-to-date and accurate information in this manual. All manufacturers, including JOBO, maintain the right to change specifications for their products. Changes may be made to specifications without notice. For the most current product specifications and usage, contact the manufacturer.
JOBO makes no claim for the accuracy or usability of other manufacturers' information contained in this manual. The processing recommendations included in this manual may not be optimal for every situation. If you require specific results, test all process instructions for suitability.
JOBO is not liable for any damages, direct or consequential, occurring from the use or misuse of information contained in this manual.
Copyright © 1997 by JOBO Fototechnic, Inc. All rights reserved. No portion of this web page may be reproduced in any form without express written consent from JOBO Fototechnic, Inc. Part number 66051. Revision 06/97.
If you have any questions, contact us utilizing one of the following methods:
Equipment or Processing Questions:
- Phone: Customer Service Department (734) 205-9421
e-mail: tech@jobo-usa.comRepair Questions:
- Phone: Repair Department (734) 205-9420
- e-mail: repair@jobo-usa.com
JOBO Contacts
- Telephone (734) 677-6989
- Fax: (734) 677-6963
- Postal address
- P.O. Box 3721, Ann Arbor, MI 48106
- Shipping Address
- 4401 Varsity Drive, Suite D, Ann Arbor, MI 48108
- Electronic mail
- Sales: sales@jobo-usa.com
- Equipment & Processing Questions: tech@jobo-usa.com
Repair Information: repair@jobo-usa.com- Shipping or Billing Questions: help@jobo-usa.com
Webmaster: webmaster@jobo-usa.com
Back to Top
Send mail to webmaster@jobo-usa.com with questions or comments about this web site. Copyright © 1997-2005 JOBO Fototechnic, Inc. All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright to all of the photographs displayed on this site is owned by each of the photographers. You may not sell, publish, license or otherwise distribute any photographs without the written permission of the photographer.
This page last updated on 03/01/05