Instructions for the

AutoLab ATL-1000 #4210
and the
AutoLab ATL 1500 #4228

1. Unpacking

Note: All instructions apply to both the ATL-1000 and ATL-1500, except where specifically noted. Only process programming differs between the two versions of the AutoLab processor.

Index

1. Unpacking

1.1 Removal from carton
1.2 Hidden damage
1.3 Packing material
1.4 Contents of carton

Return to Index Page

Back to Top

---

1.1 Removal from carton

Your unit will arrive in one carton. The shipping weight is 40 pounds (18.2 kg). To unpack the ATL-1500, cut the tape sealing the carton. Take care not to stick the knife in too far. Remove the packing material, your ATL-1500, and all the accessories.

Check that all items listed in Section 1.4 are included in the package.

---

1.2 Hidden damage

Check the processor for any damage and, if found, immediately contact the shipping company that delivered the unit or the dealer from whom you purchased the unit. According to shipping companies, it is the responsibility of the recipient to handle damage claims.

---

1.3 Packing material

Make sure to keep all packing materials in the event your need to ship the processor for any reason. The packaging will help prevent shipping damage.

---

1.4 Contents of carton

The ATL-1500 package contains the following items:

1 - ATL-1500 Processor #4228

1 - Brass hose adapter #61003

1 - Center core, one roll #04043

2 - Center core, two roll #04044

1 - Center core, extension #04045

1 - Film tank #4218

1 - Film/print tank #4219

1 - Hose for rinse water #16171

1 - Instruction manual #66054

2 - Lids for film/paper tank #91047

5 - Reel, Roll Film (35mm,120,220) #2502

1 - Reel, 4x5" sheet film #2509N

2 - Retaining plates, 4x5" #07258

2 - Retaining plates, 9x12cm #07257

1 - Rinse water pump port cap #15024

4 - Rollers #93023

1 - Solenoid valve cap #15023

2 - Stoppers for film/print drum lid #15042

1 - Tank body, 2513 #02031

NOTE:

• The Solenoid valve cap #15023, the Rinse Water Port Cap #15024, and two Roller #93023 are already installed on the processor.
• The Tank Center Cores #04043, #04044, and #04045 are shipped inside the tanks.
• The lids #91047 are shipped on the tanks.
• The reels #2502 and #2509N are shipped inside the tanks.
• The Stoppers for tank lids #15042 and two of the Rollers #93023 are shipped inside the #4218 tank.

Back to Top

---

If you have any questions, contact us utilizing one of the following methods:

Equipment or Processing Questions:

Phone: Customer Service Department (734) 205-9421
e-mail: tech@jobo-usa.com

Repair Questions:

Phone: Repair Department (734) 205-9420

e-mail: repair@jobo-usa.com

---

JOBO Contacts

Telephone (734) 677-6989

Fax: (734) 677-6963

 

Postal address

P.O. Box 3721, Ann Arbor, MI 48106

Shipping Address

4401 Varsity Drive, Suite D, Ann Arbor, MI 48108

Electronic mail

Sales: sales@jobo-usa.com

Equipment & Processing Questions:  tech@jobo-usa.com
Repair Information: repair@jobo-usa.com

Shipping or Billing Questions: help@jobo-usa.com
Webmaster: webmaster@jobo-usa.com

 

Back to Top

Send mail to webmaster@jobo-usa.com with questions or comments about this web site. Copyright © 1997-2005 JOBO Fototechnic, Inc. All rights reserved. Information in this document is subject to change without notice. Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders. Copyright to all of the photographs displayed on this site is owned by each of the photographers. You may not sell, publish, license or otherwise distribute any photographs without the written permission of the photographer.

 

This page last updated on 03/20/02